电池实验设备
您当前的位置 : 首 页 > 资讯动态 > 技术资讯

皮带输送机传动链条发生故障的几种表现形式

2020-12-21

  

皮带输送机传动链条发生故障的几种表现形式

   输送流水线:输送链条应该是最常见的一种工业链条。在工业生产过程中,尤其是在很多的食品加工中,输送机链条均以流水线的方式使用,使用范围广、使用频率高,因此也常常会发生磨损的故障,如果再加之使用方法的不当,会对链条造成极大的损伤。

  Conveying assembly line: Conveying chain should be the most common kind of industrial chain. In the industrial production process, especially in many food processing, conveyor chains are used in an assembly line, with a wide range of use and high frequency of use. Therefore, wear failures often occur. If the use method is improper, Will cause great damage to the chain.

滚筒流水线、皮带流水线、组装流水线等都是工业生产车间内最常见的几种。不同的生产工艺流程,应选择适合的流水线设备。才能在提高生产效率的同时,让它的价值充分地体现出来。针对前面的几种流水线,在使用之前,它的安装工作是非常重要的,这是直接影响到它的使用效果的。那如何正确地安装滚筒流水线呢?下面跟着小编一走来了解一下吧。

  Roller assembly lines, belt assembly lines, and assembly lines are the most common types in industrial production workshops. For different production processes, suitable assembly line equipment should be selected. In order to improve production efficiency, its value can be fully reflected. For the previous several kinds of assembly lines, its installation work is very important before use, which directly affects its use effect. Then how to install the drum assembly line correctly? Let's follow the editor to find out.

UV机.jpg

  一、铺设走线槽,连接各传输单元气源。将传输线体找正操平。电气、电源线信号安装。

  1. Lay the wiring trough and connect the air source of each transmission unit. Align and level the transmission line body. Electrical and power line signal installation.

场地定位(作标记) 流水线架子安装大脚体,在已定位好的场地上按次序摆放连接杆。

  2. Site positioning (marking) The assembly line rack is installed with large feet, and the connecting rods are placed in order on the site that has been positioned.

  三、在护板上安装电动刀插座(24V)、保险丝、挂钩,并且接电动刀插座与白先丝之间的电线,注意电动刀插座方向,有凸起边向下。

  3. Install the electric knife socket (24V), fuse and hook on the guard plate, and connect the electric wire between the electric knife socket and the white wire. Pay attention to the direction of the electric knife socket, with the raised side facing downward.

  四、安装护板前在流水线架子护板安装位臵上用5mm螺纹转打螺纹,安装走线槽、护板, 放走线槽电线和接220V插座。

  4. Before installing the guard plate, use 5mm thread to turn the thread on the installation position of the assembly line shelf guard plate, install the wire trough, guard plate, release the wire trough wire and connect to the 220V socket.

  五、线体调平,可以采用建筑线调平,调平高度可为0.625m,安装走线槽盖并用胶带固定。


  5. Line body leveling can be leveled by building line, the leveling height can be 0.625m, install the cable trough cover and fix it with tape.


标签

最近浏览:

CONTACT US

联系我们

手机:13712926617

座机:0752-6811300

邮箱:lujinxin304205@163.com

地址:博罗县园洲镇梁屋高头村兴发路86号南面



ATTENTION

关注我们

皮带输送线

扫一扫,咨询